幹壹行精壹行.
在工作上學習模具設計,而不僅僅是模具制造:
模具工程師要學會看不同類型的圖,尤其是國外的原版圖紙,熟悉本行的外文術語,查查資料即可.
學會思考:人家為什麽這樣設計?能不能改進?
如果這些都能PASS就學點結構設計的原理與實例,
最後成長為壹個懂得模具設計的產品結構設計師.
送上:
模具術語中英文對照，全面、精選 回復
組裝、沖壓、噴漆等專業詞匯
Assembly line組裝線
Layout布置圖
Conveyer流水線物料板
Rivet table拉釘機
Rivet gun拉釘槍
Screw driver起子
Electric screw driver電動起子
Pneumatic screw driver氣動起子
worktable 工作桌
OOBA開箱檢查
fit together組裝在壹起
fasten鎖緊(螺絲)
fixture 夾具(治具)
pallet棧板
barcode條形碼
barcode scanner條形碼掃描儀
fuse together熔合
fuse machine熱熔機
repair修理
operator作業員
QC品管
supervisor 課長
ME制造工程師
MT制造技術
cosmetic inspect外觀檢查
inner parts inspect內部檢查
thumb screw大頭螺絲
lbs.inch鎊、英寸
EMI gasket導電條
front plate前板
rear plate後板
chassis |'∫?si| 基座
bezel panel面板
power button電源按鍵
reset button重置鍵
Hi-pot test of SPS高源高壓測試
Voltage switch of SPS
電源電壓接柆鍵
sheet metal parts 沖件
plastic parts塑料件
SOP制造作業程序
material check list物料檢查表
work cell工作間
trolley臺車
carton紙箱
sub-line支線
left fork叉車
personnel resource department
人力資源部
production department生產部門
planning department企劃部
QC Section品管科
stamping factory沖壓廠
painting factory烤漆廠
molding factory成型廠
common equipment常用設備
uncoiler and straightener整平機
punching machine 沖床
robot機械手
hydraulic machine油壓機
lathe車床
planer |'plein?|刨床
miller銑床
grinder磨床
driller鉆床
linear cutting線切割
electrical sparkle電火花
welder電焊機
staker=reviting machine鉚合機
position職務
president董事長
general manager總經理
special assistant manager特助
factory director廠長
department director部長
deputy manager |'depjuti| =vice manager副理
section supervisor課長
deputy section supervisor =vice section superisor副課長
group leader/supervisor組長
line supervisor線長
assistant manager助理
to move, to carry, to handle搬運
be put in storage入庫
pack packing包裝
to apply oil擦油
to file burr 銼毛刺
final inspection終檢
to connect material接料
to reverse material 翻料
wet station沾濕臺
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skr?pid|報廢
scrape ..v.刮;削
deficient purchase來料不良
manufacture procedure制程
deficient manufacturing procedure制程不良
oxidation |' ksi'dei?n|氧化
scratch刮傷
dents壓痕
defective upsiding down抽芽不良
defective to staking鉚合不良
embeded lump|in'bed| |l?mp|鑲塊
feeding is not in place送料不到位
stamping-missing漏沖
production capacity生產力
education and training教育與訓練
proposal improvement提案改善
spare parts=buffer備件
forklift叉車
trailer=long vehicle拖板車
compound die合模
die locker鎖模器
pressure plate=plate pinch壓板
bolt螺栓
name of a department部門名稱
administration/general affairs dept總務部
automatic screwdriver電動啟子
thickness gauge厚薄規
gauge(or jig)治具
power wire電源線
buzzle蜂鳴器
defective product label不良標簽
identifying sheet list標示單
screwdriver holder起子插座
pedal踩踏板
stopper阻擋器
flow board流水板
hydraulic handjack油壓板車
forklift叉車
pallet棧板
glove(s)手套
glove(s) with exposed fingers割手套
thumb大拇指
forefinger食指
midfinger中指
ring finger無名指
little finger小指
band-aid創可貼
iudustrial alcohol工業酒精
alcohol container沾濕臺
head of screwdriver起子頭
sweeper掃把
mop拖把
vaccum cleaner吸塵器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain鏈條
jack升降機
production line流水線
chain鏈條槽
magnetizer加磁器
lamp holder燈架
to mop the floor拖地
to clean the floor掃地
to clean a table擦桌子
air pipe 氣管
packaging tool打包機
packaging打包
missing part漏件
wrong part錯件
excessive defects過多的缺陷
critical defect極嚴重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合規格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外觀不良
slipped screwhead/slippery screw head螺絲滑頭
slipped screwhead/shippery screw thread滑手
speckle斑點
mildewed=moldy=mouldy發黴
rust生銹
deformation變形
burr(金屬)flash(塑件)毛邊
poor staking鉚合不良
excesssive gap間隙過大
grease/oil stains油汙
inclusion雜質
painting peel off臟汙
shrinking/shrinkage縮水
mixed color雜色
scratch劃傷
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包帶折皺
painting make-up補漆
discoloration羿色
water spots水漬
polishing/surface processing表面處理
exposed metal/bare metal金屬裸露
lack of painting烤漆不到位
safety安全
quality品質
delivery deadline交貨期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise expansion projects企劃
QC品管
die worker模工
production, to produce生產
equipment設備
to start a press開機
stop/switch off a press關機
classification整理
regulation整頓
cleanness清掃
conservation清潔
culture教養
qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品
waste廢料
board看板
feeder送料機
sliding rack滑料架
defective product box不良品箱
die change 換模
to fix a die裝模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket膠筐
isolating plate baffle plate; barricade隔板
carton box紙箱
to pull and stretch拉深
to put material in place, to cut material, to input落料
to impose lines壓線
to compress, compressing壓縮
character die字模
to feed, feeding送料
transportation運輸
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料變更
feature change 特性變更
evaluation評估
prepare for, make preparations for 準備
parameters參數
rotating speed, revolution轉速
manufacture management制造管理
abnormal handling異常處理
production unit生產單位
lots of production生產批量
steel plate鋼板
roll material卷料
manufacture procedure制程
operation procedure作業流程
to revise, modify修訂
to switch over to, switch---to throw--over switching over切換
engineering, project difficulty工程瓶頸
stage die工程模
automation自動化
to stake, staking, reviting鉚合
add lubricating oil加潤滑油
shut die架模
shut height of a die架模高度
analog-mode device類模器
die lifter舉模器
argon welding氬焊
vocabulary for stamping
沖壓常詞匯
stamping, press沖壓
punch press, dieing out press沖床
uncoiler & strainghtener整平機
feeder送料機
rack, shelf, stack料架
cylinder油缸
robot機械手
taker取料機
conveyer belt輸送帶
transmission rack輸送架
top stop上死點
bottom stop下死點
one stroke壹行程
inch寸動
to continue, cont.連動
to grip(material)吸料
location lump, locating piece, block stop 定位塊
reset復位
smoothly順利
dent壓痕
scratch刮傷
deformation變形
filings鐵削
to draw holes抽孔
inquiry, search for查尋
to stock, storage, in stock庫存
receive領取
approval examine and verify審核
processing, to process加工
delivery, to deliver 交貨
to return delivenry to. to send delinery back to retrn of goods退貨
registration登記
registration card登記卡
to control管制
to put forward and hand in提報
safe stock安全庫存
acceptance = receive驗收
to notice通知
application form for purchase請購單
consume, consumption消耗
to fill in填寫
abrasion磨損
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics統計
demand and supply需求
career card履歷卡
to take apart a die卸下模具
to load a die裝上模具
to tight a bolt擰緊螺栓
to looser a bolt擰松螺栓
to move away a die plate移走模板
easily damaged parts易損件
standard parts標準件
breaking.(be)broken,(be)cracked 斷裂
to lubricate潤滑
common vocabulary for die engineering模具工程常用詞匯
die 模具
figure file, chart file圖檔
cutting die, blanking die沖裁模
progressive die, follow (-on)die
連續模
compound die復合模
punched hole沖孔
panel board鑲塊
to cutedges=side cut=side scrap切邊
to bending折彎
to pull, to stretch拉伸
Line streching, line pulling線拉伸
engraving, to engrave刻印
upsiding down edges翻邊
to stake鉚合
designing, to design設計
design modification設計變化
die block模塊
folded block折彎塊
sliding block滑塊
location pin定位銷
lifting pin頂料銷
die plate, front board模板
padding block墊塊
stepping bar墊條
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上墊板
spare dies模具備品
spring 彈簧
bolt螺栓
document folder活頁夾
file folder資料夾
to put file in order整理資料
spare tools location手工備品倉
first count初盤人
first check初盤復棹人
second count 復盤人
second check復盤復核人
equipment設備
waste materials廢料
work in progress product在制品
casing = containerazation裝箱
quantity of physical invetory second count 復盤點數量
quantity of customs count
會計師盤,點數量
the first page第壹聯
filed by accounting department for reference會計部存查
end-user/using unit(department)使用單位
summary of year-end physical inventory bills
年終盤點截止單據匯總表
bill name單據名稱
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表請與盤點清冊壹起送會計部－(NHK廠區送財會部)
Application status records of year-end physical inventory List and physical inventory card 年終盤點卡與清冊使用－狀況明細表
blank and waste sheet NO.
空白與作廢單號
plate電鍍
mold成型
material for engineering mold testing工程試模材料
not included in physical inventory不列入盤點
sample樣品
incoming material to be inspected進貨待驗
description品名
steel/rolled steel鋼材
material statistics sheet
物料統計明細表
meeting minutes會議記錄
meeting type 會別
distribution department分發單位
location地點
difference quantity差異量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods處理品
warehouse/hub倉庫
on way location在途倉
oversea location海外倉
spare parts physical inventory list備品盤點清單
spare molds location模具備品倉
skid/pallet棧板
tox machine自鉚機
wire EDM線割
EDM放電機
coil stock卷料
sheet stock片料
tolerance工差
score=groove壓線
cam block滑塊
pilot導正筒
trim剪外邊
pierce剪內邊
drag form壓鍛差
pocket for the punch head掛鉤槽
slug hole廢料孔
feature die公母模
expansion dwg展開圖
radius半徑
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺絲
form block折刀
stop pin定位銷
round pierce punch=die button圓沖子
shape punch=die insert異形子
stock locater block定位塊
under cut=scrap chopper清角
active plate活動板
baffle plate擋塊
cover plate蓋板
male die公模
female die母模
groove punch壓線沖子
air-cushion eject-rod氣墊頂桿
spring-box eject-plate彈簧箱頂板
bushing block襯套
insert 入塊
club car高爾夫球車
capability能力
parameter參數
factor系數
phosphate皮膜化成
viscosity塗料粘度
alkalidipping脫脂
main manifold主集流脈
bezel斜視規
blanking穿落模
dejecting頂固模
demagnetization去磁;消磁
high-speed transmission高速傳遞
heat dissipation熱傳
rack上料
degrease脫脂
rinse水洗
alkaline etch齡咬
desmut剝黑膜
D.I. rinse純水次
Chromate鉻酸處理
Anodize陽性處理
seal封孔
revision版次
part number/P/N料號
good products良品
scraped products報放心品
defective products不良品
finished products成品
disposed products處理品
barcode條形碼
flow chart流程窗體
assembly組裝
stamping沖壓
molding成型
spare parts=buffer備品
coordinate坐標
dismantle the die折模
auxiliary fuction輔助功能
poly-line多義線
heater band 加熱片
thermocouple熱電偶
sand blasting噴沙
grit 砂礫
derusting machine除銹機
degate打澆口
dryer烘幹機
induction感應
induction light感應光
response=reaction=interaction感應
ram連桿
edge finder巡邊器
concave凸
convex凹
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 銀紋
gas mark焦痕
delamination起鱗
cold slug冷塊
blush 導色
gouge溝槽;鑿槽
satin texture段面咬花
witness line證示線
patent專利
grit沙礫
granule=peuet=grain細粒
grit maker抽粒機
cushion緩沖
magnalium鎂鋁合金
magnesium鎂金
metal plate鈑金
lathe車
mill銼
plane刨
grind磨
drill鋁
boring鏜
blinster氣泡
fillet鑲;嵌邊
through-hole form通孔形式
voller pin formality滾針形式
cam driver鍘楔
shank摸柄
crank shaft曲柄軸
augular offset角度偏差
velocity速度
production tempo生產進度現狀
torque扭矩
spline=the multiple keys花鍵
quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel鎢高速的
moly high speed steel鉬高速的
organic solvent有機溶劑
bracket小磁導
liaison聯絡單
volatile揮發性
resistance電阻
ion離子
titrator滴定儀
beacon警示燈
coolant冷卻液
crusher破碎機
模具工程類
plain die簡易模
pierce die沖孔模
forming die成型模
progressive die連續模
gang dies復合模
shearing die剪邊模
riveting die鉚合模
pierce沖孔
forming成型(抽凸,沖凸)
draw hole抽孔
bending折彎
trim切邊
emboss凸點
dome凸圓
semi-shearing半剪
stamp mark沖記號
deburr or coin壓毛邊
punch riveting沖壓鉚合
side stretch側沖壓平
reel stretch卷圓壓平
groove壓線
blanking下料
stamp letter沖字(料號)
shearing剪斷
tick-mark nearside正面壓印
tick-mark farside反面壓印
沖壓名稱類
extension dwg展開圖
procedure dwg工程圖
die structure dwg模具結構圖
material材質
material thickness料片厚度
factor系數
upward向上
downward向下
press specification沖床規格
die height range適用模高
die height閉模高度
burr毛邊
gap間隙
weight重量
total wt.總重量
punch wt.上模重量
五金零件類
inner guiding post內導柱
inner hexagon screw內六角螺釘
dowel pin固定銷
coil spring彈簧
lifter pin頂料銷
eq-height sleeves=spool等高套筒
pin銷
lifter guide pin浮升導料銷
guide pin導正銷
wire spring圓線彈簧
outer guiding post外導柱
stop screw止付螺絲
located pin定位銷
outer bush外導套
模板類
top plate上托板（頂板）
top block上墊腳
punch set上模座
punch pad上墊板
punch holder上夾板
stripper pad脫料背板
up stripper上脫料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下墊板
die holder下夾板
die set下模座
bottom block下墊腳
bottom plate下托板(底板)
stripping plate內外打(脫料板)
outer stripper外脫料板
inner stripper內脫料板
lower stripper下脫料板
零件類
punch沖頭
insert入塊(嵌入件)
deburring punch壓毛邊沖子
groove punch壓線沖子
stamped punch字模沖子
round punch圓沖子
special shape punch異形沖子
bending block折刀
roller滾軸
baffle plate擋塊
located block定位塊
supporting block for location
定位支承塊
air cushion plate氣墊板
air-cushion eject-rod氣墊頂桿
trimming punch切邊沖子
stiffening rib punch = stinger 加強筋沖子
ribbon punch壓筋沖子
reel-stretch punch卷圓壓平沖子
guide plate定位板
sliding block滑塊